Teledyne LeCroy HDO4104 Oscilloscope

• ÷10 Passive Probe (Total of 1 Per Channel)
• Getting Started Guide
• Anti-virus Software (Trial Version)
• Microsoft Windows Embedded Standard 7 P 64-Bit License
• Commercial NIST Traceable Calibration with Certificate
• Power Cable for the Destination Country

Vertical System

• Bandwidth: 1GHz
• Rise time: 450ps
• Input Channels: four
• Bandwidth Limiters: 20MHz, 200MHz
• Input Impedance: 1MΩ ±2.0%, 15pF; 50Ω, ±2.0%
• Input Coupling: AC, DC, GND
• Maximum Input Voltage, 1MΩ: 400V max (DC + Peak AC ≤10kHz)
• Maximum Input Voltage, 50Ω: 5VRMS
• Channel-Channel Isolation: ≥24dB
• Vertical Resolution: 12 bits
• Sensitivity, 50Ω: 1mV/div to 1V/div
• Sensitivity, 1MΩ: 1mV/div to 10V/div
• DC Gain Accuracy, 50Ω: ±0.5% full scale, offset at 0V
• DC Gain Accuracy; 50Ω, ±1.6V: 1mV/div to 4.95mV/div
• DC Gain Accuracy; 50Ω, ±4V: 5mV/div to 9.9mV/div
• DC Gain Accuracy; 50Ω, ±8V: 10mV/div to 19.8mV/div
• DC Gain Accuracy; 50Ω, ±10V: 20mV/div to 1V/div
• Offset Range; 1MΩ, ±1.6V: 1mV/div to 4.95mV/div
• Offset Range; 1MΩ, ±4V: 5mV/div to 9.9mV/div
• Offset Range; 1MΩ, ±8V: 10mV/div to 19.8mV/div
• Offset Range; 1MΩ, ±16V: 20mV/div to 100mV/div
• Offset Range; 1MΩ, ±80V: 102mV/div to 198mV/div
• Offset Range; 1MΩ, ±160V: 200mV/div to 1V/div
• Offset Range; 1MΩ, ±400V: 1.02V/div to 10V/div

Horizontal System

• Time/Division Range: 200ps/div - 1.25ks/div with standard memory (up to 2.5ks/div with -L memory); RIS available at ≤10ns/div; Roll Mode available at ≥100ms/div and ≤5MS/s
• Clock Accuracy: ±2.5ppm for 5 to 40°C + 1.0ppm/year from calibration
• Trigger and Interpolator Jitter: 3.5ps rms

Acquisition System

• Single-Shot Sample Rate/Ch: 2.5GS/s
• Equivalent Sample Rate: 125GS/s
• Memory: 25Mpts/Ch on 1 Ch, 12.5Mpts/Ch on 2 Ch, 12.5Mpts/Ch on 4 Ch
• Averaging: Up to 1,000,000
• Interpolation: Linear, Sin x/x
• Enhanced Resolution: Up to 15 bits
• Sequence Mode: Up to 10,000 segments

Triggering System

• Modes Normal, Auto, Single, Stop
• Sources: Ch 1 through Ch 4, EXT, EXT/10, AC Line
• Coupling Mode: AC, DC, LF Rej, HF Rej
• Pre-trigger Delay: 0 to 100% of full scale
• Post-trigger Delay: 0 to 10,000 Divisions
• Hold-off by Time or Events: 2ns up to 20s
• Internal Trigger Range: ±4.1 Divisions
• Trigger Sensitivity, 0.9 division: 10MHz
• Trigger Sensitivity, 1.0 divisions: 200MHz
• Trigger Sensitivity, 1.5 divisions: 500MHz
• Trigger Sensitivity, 2.0 divisions: 1GHz
• External Trigger Sensitivity, 0.9 division: 10MHz
• External Trigger Sensitivity1.0 divisions, : 200MHz
• External Trigger Sensitivity, 1.5 divisions: 500MHz
• External Trigger Sensitivity, 2.0 divisions: 1GHz
• External Trigger Input Range Ext: ±0.4 V, EXT/10: ±4.0 V
• Triggers: Edge, Glitch, Width, Logic (Pattern), TV (NTSC, PAL, SECAM, HDTV), Runt, Slew Rate, Interval, Dropout, Qualified
• Optional Serial Data Triggers: I2C, SPI, UART/RS-232, CAN, LIN, FlexRay, SENT, MIL-STD-1553, ARINC 429, Audio (I2S, LJ, RJ, TDM), USB, USB-HSIC, MIPI D-PHY, DigRF3G

Internal Storage

• Media: internal hard drive, RAM
• Waveform Storage: four waveforms
• Setup Storage: six setups

Math

• Number of Math Traces: two
• Standard Math Functions: Add, Subtract, Multiply, Divide, FFT, Absolute Value, Averaging (summed and continuous), Derivative, Envelope, Enhanced Resolution, Floor, Integral, Invert, Reciprocal, Rescale, Roof, Square, Square Root, Trend, Zoom

Measurements

• Number of Measurements Displayed: eight
• Measurement Parameters: Amplitude, Area, Base, Delay, Delta Period @ Level, Delta Time @ Level, Duty Cycle, Duty @ Level, Edge @ Level, Fall Time (90% to 10%), Fall Time (80% to 20%), Frequency, Frequency @ Level, Maximum, Mean, Minimum, Overshoot+, Overshoot-, Period, Peak-Peak, Period, Period @ Level, Phase, Rise Time (10% to 90%), Rise Time (20% to 80%), RMS, Skew, Standard Deviation, Time @ Level, Top, Width+, Width-

Probes

• Quantity: four ÷10 Passive Probes
• Scale Factors, Automatic/Manual: ÷1, ÷10, ÷20, ÷100, ÷200, ÷1000, ÷2000, ÷10000
• Scale Factors, Variable: (÷1x10-6 to ÷10000)
• Calibration Output: 1kHz square wave, 1.0Vp-p, output to probe hook

Interface

• USB (Host): six
• USB (Device): one
• Ethernet Port: one
• GPIB Port: one (optional)

Mains

• Power Requirement: 90 to 264VAC @ 45Hz to 66Hz; 90 to 132VAC @ 380Hz to 420Hz
• Max. Power Consumption: 75VA

Data Sheet