Close
You have no items in your shopping cart.

CE Marking

CE marking is used to indicate that a product meets the European Union's (EU) standards for health, safety, and environmental protection. The CE mark is a requirement for the distribution of a variety of products in the EU. Meeting the safety requirements to receive CE marking is not a standard, but rather a legal requirement of the EU. When a manufacturer marks a product with the CE mark, they are declaring that it meets all of the legal requirements associated with CE marking. The CE mark allows products to be sold within the European Economic Area (EEA) without restrictions.

Rent or purchase equipment to certify your electrical product with the CE Mark from Avalon Test Equipment and Test With Confidence®.

Read More

Read Less

3 Items in Grid 4 Items in Grid List

Com-Power LI-400C LISN

10 kHz–10 MHz, 50 microhenry / 25 Amps

Com-Power LI-125C LISN

150 kHz–30 MHz

Com-Power LI-150C LISN

150 kHz–30 MHz

Teseq ISN PLT Impedance Stabilization Network

For Power Line Telecommunication (PLT) 1.6 to 30 MHz

Com-Power LIN-120A LISN

150 kHz to 30 MHz, CISPR 16-1-2 / ANSI C63.4, 50 microhenry / 20 Amps

Com-Power LI-1100C LISN

150 kHz–30 MHz

Teseq ISN PLT-A Impedance Stabilization Network

For Power Line Telecommunication (PLT)

Com-Power ISN-T8

Impedance Stabilization Network for 8 lines

Com-Power LI-3P-2x Series LISN

9 kHz–30 MHz, 50/250 uH, 500 VAC

Com-Power LI-220A LISN

For ISPR 16-1-2/ANSI C63.4, 9 kHz - 30 MHz.

Teseq ISN S502A Impedance Stabilization Network for Coaxial Lines

For use with coaxial lines, 150 kHz to 230 MHz

Teseq ISN S751 Impedance Stabilization Network for Coaxial Lines

For use with screened RJ45 connections, 150 kHz to 230 MHz

Com-Power PAM-103 Preamplifier

The Com-Power model PAM-103 Preamplifier (1MHz to 1GHz) is intended for improving measurement system sensitivity during EMC compliance testing.

A.H. Systems PAM-0118P Preamplifier

This high gain preamplifier has a rugged performance over a wide operating frequency range. The added protection of the one watt limiter is an ideal solution when testing in high fields, 20MHz to 18GHz.

Com-Power PAM-840A Preamplifier

The Com-Power PAM-840A is a wideband, high gain, bench top microwave preamplifier; 18GHz to 40GHz.

Teseq LNA 6000 Preamplifier

The Teseq LNA 6000 is a low noise amplifier with 12.5 dB of gain covering the nominal frequency range 1 MHz to 3 GHz and can be used in the range from 200 kHz to 4 GHz. With its high gain and low noise figure, it will significantly increase the sensitivity of virtually all spectrum analyzers and other RF measuring instruments.

Teseq LNA 6018 Preamplifier

The Teseq LNA 6018 is a low noise amplifier with typ. 22 dB of gain covering the nominal frequency range 1 GHz to 18 GHz. With its high gain and low noise figure, it will significantly increase the sensitivity of virtually all spectrum analyzers and other RF measuring instruments.

Com-Power PAM-6000 Preamplifier

The Com-Power PAM-6000 1 - 6 GHz High Gain Preamplifier is intended for improving measurement system sensitivity during EMC compliance testing. It has a frequency range of 1 GHz to 6 GHz. It has gain of 30 dB. Therefore, It amplifies the signals that were previously hidden below the noise floor of the EMI receiver so that it can be seen and measured.

A.H. Systems PAM-0204 Preamplifier

20 MHz - 4 GHz, 24 dB. Will improve overall system sensitivity. Designed to meet the needs of your various testing requirements.

A.H. Systems PAM-1840VH High Gain Broadband Preamplifier

18 - 40 GHz. The Preamplifier will provide reliable, repeatable measurements. An ideal solution to improve system sensitivity for compliance testing.

Com-Power PA-103 Preamplifier

100 Hz - 1000 MHz, 32dB gain

Com-Power CLA-150 Absorbing Clamp

The absorbing clamp CLA-150 was designed for EMC emissions measurement of from electrical instruments via their connecting leads. It has a 32-mm cable aperture.

Teseq FT 801 Ferrit Tube EM Decoupling Clamp

150 kHz–1 GHz, 35 mm Cable Diameter

Com-Power CLA-050 10mm Absorbing Clamp

Com-Power CLA-050 10mm Absorbing Clamp is suitable for 30 MHz - 1 GHz frequency range and offers RF disturbance power measuring, according to CISPR 14 (EN 55014)

Fischer F-33-2 Current Monitor Probe

The F-33-2 is for laboratory and field testing. The usable frequency range of this probe is 1 kHz – 250 MHz.

Com-Power AT-812 Antenna Tripod

Com-Power AT series antenna tripods are a great choice for EMC testing. They are made of non reflective nylon and wood material.