CE Mark Testing
Select Subcategory
CE marking is used to indicate that a product meets the European Union's (EU) standards for health, safety, and environmental protection. The CE mark is a requirement for the distribution of a variety of products in the EU. Meeting the safety requirements to receive CE marking is not a standard, but rather a legal requirement of the EU. When a manufacturer marks a product with the CE mark, they are declaring that it meets all of the legal requirements associated with CE marking. The CE mark allows products to be sold within the European Economic Area (EEA) without restrictions.
Rent or purchase equipment to certify your electrical product with the CE Mark from Avalon Test Equipment and Test With Confidence®.
Read More
Read Less
EM Test PFS 503N32 Power Fail Simulator
Electronic and electrical equipment may be affected by voltage dips, short interruptions and voltage variations of the power supply. Dips and interruptions are caused by faults in the public supply network, in installations or by sudden large change of load. Testing to such phenomena is required to proof that electronic and electrical equipment do not fall into unsafe operation conditions. EM TEST offers a full range of simulators up to 3x690VAC, 100A and DC voltage capability of up to 600V.
EM Test UCS 500N5 Multifunctional Test Generator
For Transients (EFT/Burst, Surge, and Power Fail) Up to 5.5KV
EM Test UCS 500N7 Multifunctional Transient Immunity Simulator
The EM Test UCS500N7 Multifunctional Transient Immunity Simulator includes everything necessary to conduct fully compliant tests at levels that go far beyond common test requirements. Surge can be tested up to 7.0kV either according to IEC/EN 61000-4-5 or ANSI/IEEE C62.41. The UCS 500N7 offers an integrated Ringwave module (optional) as per ANSI/IEEE C62.41 and IEC/EN 61000-4-12 for ringwave tests on mains supply lines.
EMC Partner ESD3000 Handheld ESD Generator
EMC Partner ESD3000 handheld ESD generator/tester with modular discharge circuits up to 30KV.
Haefely AXOS8 Compact Immunity Test System
Haefely AXOS8 Compact Immunity Test System, 7 kV integrates all of the best features of several stand-alone test systems into one single economic solution. Standards: IEC/EN 61000-4-4, -4-5, -4-9, -4-11, -4-12
Haefely IP4B Capacitive Coupling Clamp for EFT / Burst for Signal and Data Cables
Haefely IP4B Capacitive Coupling Clamp for EFT / Burst for Signal and Data Cables
M Precision ECAT High Voltage Burst/EFT Generator
M Precision ECAT High Voltage Burst/EFT Generator up to 8 kV
M Precision MiniZap-15 ESD Simulator
The MPL MZ15 ESD Simulator Gun for IEC 1000-4-2 compliance testing. Includes 150pF/330 ohm discharge network, TPA-1, TPA-2, TPC-2A discharge tips, battery charger, carrying case.
Teseq CAL CMAD20A Calibration Fixture
Calibration fixture for CMAD 20A, CMAD 20B, Lüthi FTC 40x15 E according CISPR 16-1-4
Teseq CAS 3025 Burst/EFT Pulse Verification Kit
The Teseq CAS 3025 burst/EFT pulse verification kit has been specially designed to comply with the new requirements of IEC/EN 61000-4-4:2004 to enable EMC engineers to verify their burst/EFT test generators periodically.
Teseq CAS CDNE Calibration Kit for CDNE
The Teseq CAS CDNE Calibration Kit provides measurements for CM impedance and phase angle, VDF, decoupling attenuation and DM impedance
Teseq CAS ISN Extension for T2
The calibration kit CAS ISN is made for function tests and remeasurements on impedance stabilization network (ISN) for unshielded balanced pairs. Measuring parameters are common mode (CM) impedancence, phase angle, voltage division factor, decoupling attenuation (isolation) and longitudinal conversion loss (LCL). Impedance stabilization networks (ISN) are defined in CISPR 22 and CISPR 16-1-2.
Teseq CDN 3043-B32 3-Phase Coupling/Decoupling Network
competitively priced, high performance extension to the NSG 3040 multifunction generator series.
Teseq CDN 3043-C32 3-Phase Coupling/Decoupling Network
competitively priced, high performance extension to the NSG 3040 multifunction generator series.
Teseq CDN 3043-S32 3-Phase Coupling/Decoupling Network
CDN 3043 3-phase coupling/decoupling network series as a competitively priced, high performance extension to the NSG 3040 multifunction generator series.
Teseq CDN 3425 Burst/EFT Coupling Clamp
The CDN 3425 is Teseq’s newly designed Burst EFT coupling clamp.
Teseq INA 417B Opto-link
The Teseq INA 417B Opto-link to a PC product is compatible of Teseq NSG 438A
Teseq INA 5530 Automotive EFT Pulse Verification Kit
ISO 7637 Automotive Pulse 3a & 3b Verification Kit
Teseq INA 6501 Manual Step Transformer
Teseq INA 6501 Manual Step Transformer for AC Dips & Interruptions
Teseq MD 102A ESD Pulse Measurement Target for IEC/EN 61000-4-2
ESD measurement target conforming to IEC/EN 61000-4-2
Teseq MD 103 ESD Pulse Calibration Set
Target for precise ESD pulse measurements, very small insertion loss variation, precise gold plated construction
Teseq NSG 3040-IEC Multifunction Burst Generator
Teseq’s new NSG 3040 is an easy-to-use multifunction generator that simulates electromagnetic interference effects for immunity testing in conformity with international, national and manufacturers’ standards including the latest IEC/EN standards.