Close
You have no items in your shopping cart.

Amplifier Research 150A100A Amplifier

Manufacturer part number: 150A100A
The 150A100A is a 100 MHz, 150 W RF amplifier from Amplifier Research. Amplify RF and Microwave signals to measure, test, and design circuits. Applications include radio communications, cellphones, EMI testing, and much more.
PURCHASE
AvailableQTYPrice
New:   0
+ -
$0.00
Used:   1
+ -
$7,775.00Configurations
X

Available Configurations

AMPLIFIER, 10 KHZ - 100 MHZ 150W
30009251
$7775

The Amplifier Research Model 150A100A amplifier is a self-contained, broadband unit designed for laboratory applications where instantaneous bandwidth, high gain and moderate power output are required. Utilization of push-pull MOSFET circuitry lowers distortion, improves stability and allows operation into any load impedance without damage. The Model 150A100A, when used with an RF sweep generator, will provide a minimum of 150 watts of swept power.

There is a digital display on the front panel to indicate the operate status and fault conditions when an over temperature, power supply, or amplifier fault has occurred. The unit can be returned to operate when the condition has been cleared. The 150A100A includes digital control for both local and remote control of the amplifier. Housed in a stylish, contemporary enclosure, the Model 150A100A provides readily available RF power for typical applications such as RF susceptibility testing, antenna and component testing, watt meter calibration, and use as a driver for higher power amplifiers.

  • Rated Power Output: 150 watts
  • Input for Rated Output: 1.0 milliwatt maximum
  • Power Output @ 3db Compression: Nominal: 220 watts; Minimum: 180 watts
  • Power Output @ 1db Compression: Nominal: 155 watts; Minimum: 125 watts
  • Flatness: ± 1.5 dB maximum
  • Frequency Response: 10 kHz-100 MHz instantaneously
  • Gain: 52 dB minimum
  • Gain Adjustment Range: 18 dB minimum
  • Input Impedance: 50 ohms, VSWR 1.5:1 maximum
  • Output Impedance: 50 ohms, VSWR 2.0:1 maximum
  • Mismatch Tolerance: 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance.
  • Modulation Capability: Will faithfully reproduce AM, FM, or pulse modulation appearing on the input signal
  • Noise Figure (above 1.0 MHz): 6 dB typical
  • Harmonic Distortion: Minus 20 dBc maximum at 125 watts
  • Third Order Intercept Point: 58 dBm typical
  • Primary Power: 90-135/180-270 VAC auto ranging 47-63Hz, single-phase. 1000 watts maximum
  • Remote Control: IEEE-488: 24 pin male; RS-232: 9 pin Subminiature D (male)
  • Remote Interlock: 15 Pin Subminiature D
  • Cooling: Forced air (self-contained fans)
  • Calibration Certificate
Description

The Amplifier Research Model 150A100A amplifier is a self-contained, broadband unit designed for laboratory applications where instantaneous bandwidth, high gain and moderate power output are required. Utilization of push-pull MOSFET circuitry lowers distortion, improves stability and allows operation into any load impedance without damage. The Model 150A100A, when used with an RF sweep generator, will provide a minimum of 150 watts of swept power.

There is a digital display on the front panel to indicate the operate status and fault conditions when an over temperature, power supply, or amplifier fault has occurred. The unit can be returned to operate when the condition has been cleared. The 150A100A includes digital control for both local and remote control of the amplifier. Housed in a stylish, contemporary enclosure, the Model 150A100A provides readily available RF power for typical applications such as RF susceptibility testing, antenna and component testing, watt meter calibration, and use as a driver for higher power amplifiers.